
**********************************************************************
*                       SMC Technology Corporation                   *
*                       SMC TigerCard 1000 adapter                   *
*              NetWare Server Driver Installation Overview           *
*                                                                    *
*            Copyright (C) 1999 by SMC Technology Corporation.       *
*                         All rights reserved.                       *
**********************************************************************

Contents:
                A. File Description
                B. Driver Installation for NetWare Server 3.12
                C. Driver Installation for NetWare Server 4.11
                D. Driver Installation for NetWare Server 5.0

A. File Description
--------------------

-------------------------------------------------------------------------------
Filename              Description
-------------------------------------------------------------------------------
SERVER.TXT            This file. Presents a summary of the contents for
                      NetWare Server driver installation.

SMC9462.LAN           SMC's 32-Bit ODI Server driver for TigerCard 1000 for
                      NetWare Server 3.12,4.11, 5.0

SMC9462.LDI           The (SMC9462.LAN) driver installation information
                      file for NetWare Server 4.11, 5.0

-------------------------------------------------------------------------------

B. Driver Installation for NetWare Server 3.12

   Note: Prior to intalling SMC9462.lan ODI driver, you should upgrade
         to patch kid D(312ptd.exe,see Novell Document No:2936137) or later,
         or install 3.2 Enhacement Pack(for Netware 3.2).The 3.2 Enhacement Pack
         may be purchased from your Novell reseller.
         Next step you will patch ODI33f.exe or later program(see Novell
         document No:2943476) to support Novell's latest automated services.
         Finally, You should install loader patch.Assuming the Netware server
         is installed in c:\nwserver subdirectory and the 312ptd has been
         extracted into the c:\312ptd subdirectory, the following commands can
         be used to install the loader patch:

                copy c:\312ptd\native\loader\*.* c:\nwserver
                cd c:\nwserver
                lswap loader.exe server.exe


         To install the driver:

         1. Insert SMC's SMC TigerCard Driver Diskette in your PC's
            floppy drive (A:).
         2. Change to the NetWare Server directory (for example:
            CD\NWSERVER)
         3. Copy the following files from Driver Diskette to the NetWare
            Server directory.

                   \NETWARE\ODI\SERVER\SMC9462.LAN

         4. Sample AUTOEXEC.NCF for NetWare Server 3.12

             AUTOEXEC.NCF
             ============
                LOAD C:SMC9462 slot=3 FRAME=ETHERNET_802.2 NAME=E_8022
                BIND IPX to E_8022 NET=10
                LOAD C:SMC9462 slot=3 FRAME=ETHERNET_II NAME=E_II
                BIND IPX to E_II  NET=30
                LOAD C:SMC9462 slot=3 FRAME=ETHERNET_802.3 NAME=E_8023
                BIND IPX to E_8023 NET=20
                LOAD C:SMC9462 slot=3 FRAME=ETHERNET_SNAP NAME=E_SNAP
                BIND IPX to E_SNAP NET=40

         5. Reboot the Netware Server and TigerCard 1000  driver will launch
            automatically for NetWare Server 3.12.

------------------------------------------------------------------------

C. Driver Installation for NetWare Server 4.11

   1. Shutdown your computer and install the TigerCard NIC in a PCI slot.
      Connect the NIC to the network using a fiber optic cable.

   2. Turn your computer on and boot it to the NetWare 4.11 console prompt.

   3. At the NetWare console prompt enter the command load install to start 
      the install utility. The Installation Options dialog box is displayed.

   4. Select the Driver Options menu item and press enter. The Driver Options 
      dialog box is displayed.

   5. Select the Configure Network Drivers menu item and press enter. The 
      Additional Driver Actions dialog box is displayed.

   6. Insert the TigerCard 1000 Driver Diskette into the 'A' drive.

   7. Select the Load an additional driver menu item option and press enter. 
      The Select a driver dialog box is displayed. Press the Ins key to 
      Install an unlisted driver. A dialog box indicating the A drive will 
      be scanned for drivers is displayed. Press enter to continue. 

   8. Press enter to select the SMC9462.LAN from the Select a driver to install
      dialog box. A message asking if you want to copy the driver is displayed.
      Select Yes to continue.  The device driver is copied.

   9. A screen with three dialog boxes is displayed. To change the driver 
      configuration, tab to the SMC9462_1 Parameters dialog box and modify
      the driver parameters. Depending on the network the NIC is attached to, 
      the Link Speed, Duplex Mode, and Phy Type parameters might need to be 
      changed from their default values.  If you are not sure what values are 
      required for your network, contact your network administrator.

  10. Tab to the SMC9462_1 Protocols and select the desired protocols.
  11. Tab to the Board SMC9462_1 Actions dialog box. Select the Save Parameters
      and Load Driver option and press enter to continue.

  12. Perform protocol specific configuration as required.

  13. Select No when asked if you want to load additional drivers.

  14. On the Additional Driver Actions dialog box, select Return to previous
      menu and press enter to continue.

  15. On the Driver Options dialog box, select Return to previous menu and 
      press enter to continue.

  16. On the Installation Options dialog box, select Exit to return to the 
      NetWare console prompt.

--------------------------------------------------------------------------

D. Driver Installation for NetWare Server 5.0

   1. Shutdown your computer and install the TigerCard NIC in a PCI slot.
      Connect the NIC to the network using a fiber optic cable.

   2. Turn your computer on and boot it to the NetWare 5.0 console prompt.

   3. At the NetWare console prompt enter the command load nwconfig to start
      the install utility. The Installation Options dialog box is displayed.

   4. Select the Driver Options menu item and press enter. The Driver Options 
      dialog box is displayed.

   5. Select the Configure Network Drivers menu item and press enter. The 
      Additional Driver Actions dialog box is displayed.

   6. Insert the TigerCard 1000 Driver Diskette into the 'A' drive.

   7. Select the Load an additional driver menu item option and press enter. 
      The Select a driver dialog box is displayed. Press the Ins key to 
      Install an unlisted driver. A dialog box indicating the A drive will 
      be scanned for drivers is displayed. Press enter to continue. 

   8. Press enter to select the SMC9462.LAN from the Select a driver to install
      dialog box. A message asking if you want to copy the driver is displayed.
      Select Yes to continue.  The device driver is copied.

   9. A screen with three dialog boxes is displayed. To change the driver 
      configuration, tab to the SMC9462_1 Parameters dialog box and modify
      the driver parameters. Depending on the network the NIC is attached to, 
      the Link Speed, Duplex Mode, and Phy Type parameters might need to be 
      changed from their default values.  If you are not sure what values are 
      required for your network, contact your network administrator.

  10. Tab to the SMC9462_1 Protocols and select the desired protocols.
  11. Tab to the Board SMC9462_1 Actions dialog box. Select the Save Parameters
      and Load Driver option and press enter to continue.

  12. Perform protocol specific configuration as required.

  13. Select No when asked if you want to load additional drivers.

  14. On the Additional Driver Actions dialog box, select Return to previous
      menu and press enter to continue.

  15. On the Driver Options dialog box, select Return to previous menu and 
      press enter to continue.

  16. On the Installation Options dialog box, select Exit to return to the 
      NetWare console prompt.





All trademarks and brand names mentioned belong to their
respective owners.

-- End of File --
